- LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ MANUAL
- LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ FULL
- LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ PROFESSIONAL
You do not have to use the digital channel for your 'master' mix, but this is recommended in order to avoid introducing additional analogue noise. You can also use the master volume control to mute selected outputs. You can enable 'Mixer' on any other mix tab, solo the DI signal, and you will hear the DO 1/2 mix through those outputs. The DO 1/2 mix is now available as DI inputs on all other mixes. Now connect the digital ports back-to-back, with a BNC or TOSLINK cable. Next, ensure that the DI channels are muted on the DO 1/2 mix, and ensure that your DAW signal is sent to the DO 1/2 channels. However, you can use a low-latency mix as an auxiliary channel to achieve the same effect.įor example, you could configure an auxiliary mix on the DO 1/2 tab, using headphone monitoring to check the levels, pans, etc. There is no way to directly route outputs to different channels. Orpheus mixes apply to specific output pairs. How do I route the same DAW stereo signal to different Orpheus output pairs?
LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ PROFESSIONAL
Professional DAWs usually have a 'Pre-delay' setting, or sample offset value, that you can set equal to the round-trip latency, so that it is played back in time with the pre-recorded backing track. The vocal will be mixed with the DAW output in hardware and sent to the headphones, but the unmixed vocal will be recorded independently by the DAW on AI1.įinally, you need to compensate for the recording delay. Ensure that the vocal is not monitored as it records in the DAW, and send the pre-recorded track to the Orpheus HP outputs. Open the HP mixer tab on the Orpheus control panel and select 'Mixer' from the drop list. The round-trip delay may be unacceptable. The vocal will already be delayed by the input latency amount before it is recorded, and there is a further delay due to the output delay before the vocalist hears her own voice in the headphones. If a foldback mixer is not used, the vocal will have to be mixed in the DAW. Round-trip latency delays are usually irrelevant when a suitable low-latency foldback mix is used.Ĭonsider a vocalist singing over a backing track that is already recorded on the computer.The backing track is played to the Headphone outputs (say) and the vocal is being recorded on AI1. In addition, your DAW will introduce some latency as it buffers audio.
LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ MANUAL
See the Stability and Latency section of the manual for more information. In order to minimise the risk of audio drop-outs, we recommend that you set the latency fairly high. How does Orpheus compensate for system latency?
LOGIC PRO 10.4 PROBLEMAS CON INTERFAZ FULL
If the hard drive is on a separate bus, the full channel count is available. This effectively halves the number of channels that can be used. When playing, audio data has to be streamed from the drive, to the DAW and to Orpheus.
When recording, audio data has to be streamed from Orpheus, to the DAW and then to the drive. You will also cut available bandwidth if you put your hard drive on the same FireWire bus. If you have a FireWire expansion card as well as built-in FireWire, you will have two separate buses, so you can put Orpheus on one and a hard drive on the other. However, they may have several FireWire ports on this bus, and they could be a mixture of S800 & S400 ports.ĭevices cannot interact if they are on different FireWire buses. Most expansion cards have several FireWire ports on a single bus.Īll Apple Macs have a single internal FireWire bus. Note that there may be more than one FireWire port on the same bus. In order to guarantee that drop-outs do not occur, we recommend that you do not share the FireWire bus with other devices. However, some devices, including many external hard drives, are not compatible and will cause audio drop-outs.
Most FireWire devices are perfectly compatible with Orpheus. Reference material and downloadable resourcesĬan I use Orpheus at the same time as other FireWire devices?
Link to Prism Sound Logging and Transcription site Link to Prism Sound Test and Measurement site Jobs, careers and opportunities at Prism Sound